Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
+ Mechanical part of engine G16
- Mechanical part of engine J20
+ The general description
- Routine maintenance
Compression check
Check of depression of the engine
Check of pressure of oil
Filtering element of the air filter
The case throttle заслонок and an inlet collector
Exhaust system collector
Cover of a head of the cylinder
Маслосборник and a grid of the oil pump
The oil pump
Cover of a chain of synchronisation
The second chain of synchronisation and натяжитель chains
The first chain of synchronisation and натяжитель chains
Cam-shafts and regulators клапанного a backlash
Valves and head of the block of the cylinder
Pistons, piston rings, rods and cylinders
+ Assembly armature of the engine
The special tool
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
+ Engine cooling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Маслосборник and a grid of the oil pump
Components
|
|
*1) Put hermetic 99000-31250 on the interfaced surfaces маслосборника and the pallet картера, having addressed to point 1 of procedure of installation. |
|
|
The rotating moment of an inhaling. |
Removal
|
|
- Take out oil probe.
- Lift a vehicle and remove both lobbies of a wheel.
- Remove a box of the steering mechanism (4) from a vehicle.
- Remove the case of forward differential (1) with differential (2) from the chassis. Address to Section Removal in the Head Forward differential.
|
|
1 — the case of forward differential
2 — differential
3 — маслосборник |
- Merge engine oil, having opened a drain stopper.
- Remove an element of rigidity of transmission if that is available.
- Remove the bottom plate of the case муфты (картера the hydrotransformer).
- Remove маслосборник and a grid of the oil pump (2) with картера.
|
|
1 — the oil pump
2 — a grid of the oil pump |
|
|
Cleaning
|
| |
- Inside маслосборника and the screen of a grid of the oil pump.
|
| |
- Clean a condensed surface on маслосборнике and картере. Remove oil, old hermetic and a dust from a condensed surface.
|
|
|
Installation
|
|
- To facilitate and provide installation маслосборника, increase a backlash between the engine and the vehicle case according to the following procedure.
- Remove a rack support.
- Disconnect an exhaust pipe from an exhaust system collector.
- Remove nuts of fastening of the engine (right and left).
- By means of the adaptation for engine lifting at installation, lift the engine on 2 – 3 sm (about 1 inch).
|
|
|
|
Do not lift the engine more than it is specified above. It can lead to engine or transmission damage. |
|
- Put hermetic on the interfaced surface маслосборника (1) continuously. "And": hermetic 99000-31250.
|
|
"And" — 2 mm (0.08 inches)
b — 3 mm (0.12 inches) |
- Put кольцеобразные consolidations (2), and establish a grid of the oil pump (3) on маслосборник (1). At first twirl grid bolts, and then a bolt of an arm with the specified rotating moment.
- The rotating moment of an inhaling:
- Bolt of a grid of the oil pump () — 11 Н•м (1.1 kg th, 8.0 pound on foot)
- Bolt of an arm of a grid of the oil pump (b) — 11 Н•м (1.1 kg th, 8.0 pound on foot)
|
|
- After installation маслосборника (4) on the pallet картера, insert tightening bolts and start to tighten at the centre: turn a wrench outside, twisting on one bolt at a time. Fasten bolts and nuts with the specified rotating moment. The rotating moment of an inhaling: a bolt and a nut маслосборника () — 11 Н•м (1.1 kg th, 8.0 pound on foot).
|
- Lower the engine and fasten nuts of fastening of the engine with the specified rotating moment, having addressed to Section the Engine in this Chapter.
|
|
- Insert a new lining and a drain stopper (2) in маслосборник (1). Fasten a drain stopper with the specified rotating moment. The rotating moment of an inhaling: a drain stopper () — 50 Н•м (5.5 kg th, 36.5 pound on foot).
|
- Establish the bottom plate of the case муфты (картера the hydrotransformer).
- Connect an exhaust pipe №1 to an exhaust system collector, having addressed to Section an exhaust system Collector in this Chapter.
- Establish an element of rigidity of transmission on transmission and the cylinder block if that is available.
- Establish the case of forward differential according to procedure of the installation described in Section Installation in the Head Forward differential.
- Fill the case of forward differential трансмиссионным with oil, having addressed to Servicing in the Head Forward differential.
- Establish a box of the steering mechanism in a vehicle, having addressed to Section Carter of the wheel hydraulic booster in the Head System of the hydraulic booster of a wheel.
- Establish oil probe.
- Fill the engine with engine oil, having addressed to Section Engine oil and the filter in the Head Maintenance service and greasing.
- Fill in in system of a steering with strengthening a special liquid, having addressed to Section the Liquid of the hydraulic booster of a wheel in the Head System of the hydraulic booster of a wheel.
- Check up, whether leaks engine oil, oil of differential and a steering liquid on each connection.
|
|
|
|