Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
+ Mechanical part of engine G16
- Mechanical part of engine J20
+ The general description
- Routine maintenance
Compression check
Check of depression of the engine
Check of pressure of oil
Filtering element of the air filter
The case throttle заслонок and an inlet collector
Exhaust system collector
Cover of a head of the cylinder
Маслосборник and a grid of the oil pump
The oil pump
Cover of a chain of synchronisation
The second chain of synchronisation and натяжитель chains
The first chain of synchronisation and натяжитель chains
Cam-shafts and regulators клапанного a backlash
Valves and head of the block of the cylinder
Pistons, piston rings, rods and cylinders
+ Assembly armature of the engine
The special tool
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
+ Engine cooling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
The case throttle заслонок and an inlet collector
Components
Removal
|
|
- Dump fuel pressure.
- Disconnect a negative cable from the accumulator.
|
|
In order to avoid a burn, do not open a stopper of a drain aperture and a radiator cover if the engine and a radiator have not cooled down yet. A burning liquid and steam can be pulled out outside under pressure if the stopper and a cover are opened too early. |
- Remove a final hose of the air filter.
|
|
- Disconnect following electric conclusions:
- Valve socket recycling the fulfilled gases
- Socket of the valve of the control of idling
- Socket of the gauge of position of the case throttle заслонок
- Socket of the gauge of absolute pressure in an inlet collector
- Clip of grounding from an inlet collector
- The gauge of the multidimensional adjusting characteristic
|
- Disconnect a rope of an accelerator and a cable of a drive throttle заслонок А/Т (for models А/Т) from the case throttle заслонок.
|
|
- Disconnect following hoses:
- Brake hose from an inlet collector
- Hose of compulsory ventilation картера from an inlet collector
- Vacuum hose of a regulator of fuel pressure from an inlet collector
- Vacuum hose from the valve of absolute pressure in an inlet collector
- Vacuum hose from an inlet collector
- Water hoses from the case throttle заслонок and a water bypass pipe
- Hose сапуна from the case throttle заслонок
- Hose of giving of fuel and returnable hose from each pipe
|
- Remove a pipe of giving of fuel with fuel injectors from a cylinder head.
- Remove forward and back elements of rigidity of an inlet collector.
- Disconnect a water pipe from an inlet collector.
|
|
- Remove an inlet collector (1) from a head of the cylinder (2), and then its lining (3).
|
|
|
Installation
|
|
- Repeat dismantling procedure upside-down for the purpose of installation, without forgetting about the following.
|
|
- Use a new lining for an inlet collector (1).
|
- Establish a pipe of giving of fuel with fuel injectors on a cylinder head.
|
|
- Adjust люфт a rope of an accelerator and люфт a cable of a drive throttle заслонок А/Т (for models А/Т).
|
- Check up, whether all removed parts are put into place. Repeatedly establish any necessary parts which have not been earlier established.
- Back fill cooling system, having addressed to Section Washing and filling of system of cooling in the Head engine Cooling.
- On termination of installation turn the ignition key on ВКЛ, leaving the engine switched off, and check up fuel leak.
- At last, include the engine and check up, whether engine antifreeze proceeds.
|
|
|
|