Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
   + Mechanical part of engine G16
   - Mechanical part of engine J20
      + The general description
      - Routine maintenance
         Compression check
         Check of depression of the engine
         Check of pressure of oil
         Filtering element of the air filter
         The case throttle заслонок and an inlet collector
         Exhaust system collector
         Cover of a head of the cylinder
         Маслосборник and a grid of the oil pump
         The oil pump
         Cover of a chain of synchronisation
         The second chain of synchronisation and натяжитель chains
         The first chain of synchronisation and натяжитель chains
         Cam-shafts and regulators клапанного a backlash
         Valves and head of the block of the cylinder
         Pistons, piston rings, rods and cylinders
      + Assembly armature of the engine
      The special tool
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
   + Engine cooling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment




The first chain of synchronisation and натяжитель chains

1 — the first chain of synchronisation
2 — a directing wheel
3 — an axis of a directing wheel
4 — a synchronisation asterisk коленвала
5 — натяжитель synchronisation chains
6 — a regulator натяжителя chains of synchronisation №1

7 — directing to a chain of synchronisation №1
8 — a nut натяжителя synchronisation chains
9 — распорная the plug натяжителя synchronisation chains
10 — a regulator bolt натяжителя chains of synchronisation №1
11 — a bolt of a directing chain of synchronisation


The rotating moment of an inhaling.

Grease with engine oil sliding surfaces.

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative cable from the accumulator.
  2. Merge engine oil.
  3. Merge antifreeze.
  4. Remove маслосборник and a grid of the oil pump, having addressed to Razdelu Maslosbornik and a grid of the oil pump in this Chapter.
  5. Uncover cylinder heads, having addressed to Section the Cover of a head of the cylinder in this Chapter.
  6. Uncover synchronisation chains, having addressed to Section the Cover of a chain of synchronisation in this Chapter.
  1. Repeatedly to establish a synchronisation chain, turn коленвал so that marks of synchronisation in a head of the cylinder and the cylinder block coincided with marks in asterisks.
  1. Remove the second chain of synchronisation, having addressed to Section the Second chain of synchronisation and натяжитель chains in this Chapter.
  2. Remove directing to a chain of synchronisation №1 (1).
  3. Remove a regulator of a tension of a chain of synchronisation №1 (2).
  1. Remove натяжитель chains of synchronisation (3).
  1. Remove directing wheel and the first chain of synchronisation.
  2. Remove a synchronisation asterisk коленвала.

Check

Directing to a chain of synchronisation №1

Check up a boot on deterioration or damage presence.

1 — directing to a chain of synchronisation №1

Натяжитель synchronisation chains

Check up a boot (1) about deterioration or damage.

Synchronisation asterisk коленвала

Check up a teeth of an asterisk about deterioration or damage.

Directing wheel

Check up a teeth and the plug (1) asterisks about deterioration or damage.

The first chain of synchronisation

Check up a synchronisation chain on deterioration or damage presence.

Regulator of a tension of a chain of synchronisation №1

Be convinced of that a latch (1) and a gear surface (2) are not damaged also a latch functions normally.

Installation

 PERFORMANCE ORDER

  1. Level a key of an asterisk of synchronisation of a knee (1) with a mark of synchronisation (2) on the cylinder block.
  1. Establish a synchronisation asterisk коленвала (2). The conformity mark looks towards a chain cover.
1 — коленвал
2 — the cylinder block
4 — a mark
  1. Oil the plug of a directing wheel (1).
  2. Establish an axis of an asterisk and directing wheel.
  1. Establish the first chain of synchronisation (3), having levelled a dark blue plate (4) first chains of synchronisation with a mark of conformity (2) on a directing wheel.
  1. Level a yellow plate (4) 1st chains of synchronisation (3) with a mark of conformity (2) on a synchronisation asterisk коленвала (1).
  1. Establish натяжитель chains of synchronisation (1). The rotating moment of an inhaling: a nut натяжителя synchronisation chains () — 25 Н•м (2.5 kg th, 18.5 pound on foot).
1 — натяжитель synchronisation chains
2 — распорная the plug
  1. Having opened a latch (2) regulators of a tension №1 and having pressed плунжер (1) into the case (3), fix it in this position, having inserted a lock core (4) between a latch and the case.
  1. Establish a regulator of a tension of a chain of synchronisation №1 (1). The rotating moment of an inhaling: a bolt натяжителя chains of synchronisation №1 () — 11 Н•м (1.1 kg th, 8.0 pound on foot).
  2. Pull out a lock core (3) of a regulator №1.
1 — a regulator of a tension of a chain of synchronisation
2 — натяжитель synchronisation chains
3 — a lock core
  1. Establish directing to a chain of synchronisation №1 (1). The rotating moment of an inhaling: a bolt of a directing chain of synchronisation () — 9 Н•м (0.9 kg th, 6.5 pound on foot).
1 — directing to a synchronisation chain
2 — bolts directing
  1. Check up, that a dark blue plate (2) and a yellow plate (4) first chains of synchronisation coincided with marks of conformity in asterisks.
1 — a mark of conformity in a directing wheel
2 — a mark of conformity in an asterisk of synchronisation of a knee
3 — a label
4 — a yellow plate
  1. Establish the second chain of synchronisation, having addressed to Section the Second chain of synchronisation and натяжитель chains in this Chapter.
  2. Establish a cover of a chain of synchronisation, having addressed to Section the Cover of a chain of synchronisation in this Chapter.
  3. Establish a cover of a head of the cylinder, having addressed to Section the Cover of a head of the cylinder in this Chapter.
  4. Establish маслосборник and a grid of the oil pump, having addressed to Razdelu Maslosbornik and a grid of the oil pump in this Chapter.
  5. Establish system of cooling and other parts.
  6. Fill in in system of cooling antifreeze, in forward differential трансмиссионное oil, in the engine engine oil and in system of a steering with strengthening a special liquid.
  7. Check up, whether there is no leak of antifreeze, a liquid for system of a steering, leak of exhaust gas and oil on each connection.