Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation



Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
- Transmissions
   + Mechanical transmission (type 1)
   + Mechanical transmission (type 2)
   - Automatic transmission (4 A/T)
      + The general description
      + Diagnostics of an automatic transmission
      + Safety measures at diagnostics of malfunctions
      + Visual survey
      - Service out of a workshop
         Liquid level
         Liquid replacement
         Hoses of a cooler of oil
         Cable of a throttle of an automatic transmission
         The manual selector
         Gear change cable
         The switch (gauge) of a range of transmission
         The gauge of speed on an exit of an automatic transmission
         The interruption switch on demand
         Solenoidal valves
         The switch of change of a food \norm
         Tubes of a cooler of oil
      + System of blocking of brakes
      + System check
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment




Solenoidal valves

Solenoidal valves of switching and solenoidal valve TCC

Check

Having disconnected сцепки the electronic block of management (РСМ) and by means of a service wire, check up each solenoidal valve on click presence.

Engines G16/20

1 — a service wire
2 — the disconnected sockets of the electronic block of management (РСМ)

Engines G16/20

The solenoidal valve of switching (№1)

С51-1-2

The solenoidal valve of switching-in (№2)

С51-1-1

Solenoidal valve TSS (blocking)

С51-1-8

Removal

 PERFORMANCE ORDER

  1. Take out oil probe and lift the car.
  2. Allow to the engine to cool down, remove a drain stopper from the pallet картера and merge a liquid of an automatic transmission.
  3. Establish a drain stopper with a lining. The inhaling moment (a): 23 Н•м (2.3 kg th, 17.0 pounds-foots).
  4. Remove an arm of an exhaust pipe and disconnect forward карданный a shaft from forward differential (if is).
  5. Remove pallet bolts картера.
  6. Remove the pallet картера.
  7. Remove tubes for oil.
  8. Remove the solenoidal valve №1 (the solenoidal valve of switching and) or the solenoidal valve №2 (solenoidal valve TSS).
1 — a drain stopper
2 — карданный a shaft

Work check

 PERFORMANCE ORDER

  1. Each time, removing solenoidal valves of switching and solenoidal valve TSS (blocking) from a transmission, check their physical serviceability before installation into place.
  2. Put a butterdish трансмиссионную a liquid on the solenoidal valve and, having squeezed hands, check up, that трансмиссионная the liquid from a butterdish did not leave apertures of the solenoidal valve when pressure of the battery is not connected.
  3. Under the conditions described above connect pressure of the battery and be convinced that the liquid vigorously leaves.
  • If the liquid does not leave vigorously at performance of the second point of check, do not use repeatedly this solenoidal valve.
  • In drawing check of the solenoidal valve of switching at the left is shown. Check up solenoidal valve TSS similarly.

Without pressure of the battery

1 — a butterdish (with трансмиссионной a liquid)
2 — the solenoidal valve
3 — the battery
And — an aperture (should be dry)
In — a let out liquid

With pressure of the battery

1 — a butterdish (with трансмиссионной a liquid)
2 — the solenoidal valve
3 — the battery
And — an aperture (should be dry)
In — a let out liquid

Installation

For installation of solenoidal valves execute removal procedure upside-down, paying attention to the following:

 PERFORMANCE ORDER

  1. Use a new lining and the O-shaped ring.
  1. Establish tubes for oil in such sequence which is shown in drawing.
  1. Use a new lining of the pallet картера.
  2. Tighten universal фланцевые bolts and nuts of the hinge and bolts of an arm of an exhaust pipe to the specified value of the moment of an inhaling.
  3. Fill in трансмиссионную a liquid and check up its level as it is described earlier in Section liquid Replacement.
  4. After a warming up of an automatic transmission check up, whether there is no liquid leak.