Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
- Brake system
+ Brakes
+ Brake highway/hose the brake cylinder
+ Forward brakes
- Lay and back brake
+ The general description
- Diagnostics
Check and adjustment
Vehicle service
Cable of a lay brake
Brake drum
Brake колодка
The brake cylinder
Back plate of a brake
+ Antiblocking brake system (ABS)
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Brake колодка
|
|
- If the overlay is worn out beyond the limit, replace a boot.
- If one of brake overlays is worn out to a limit, it is necessary to replace all overlays simultaneously.
- Thickness brake Pads "a":
- The standard: 6.5 mm (0.24 inches)
- Deterioration limit: 3.0 mm (0.12 inches)
|
|
Never polish an overlay with an emery paper. If to polish with its emery paper, rigid particles from an emery paper remain on an overlay and can damage a drum. When it is necessary to correct an overlay, replace it with the new. |
|
|
Installation
|
|
The Note in the beginning of the given Chapter see. |
|
|
- Before installation of a brake drum, check up external diameter brake Pads (3). If it does not correspond to the value resulted more low, adjust it according to specifications, having turned a regulator (4). External diameter brake Pads: "a" — 219.4 - 219.7 mm (8.638 - 8.650 inches).
|
|
1 — the lock lever
2 — a regulator pin |
- Establish a brake drum, having convinced that an internal part of a brake drum and brake колодок are free from a dirt and oil.
- On termination of works, press the brake lever with effort about 30 kg (66 pounds) from three to ten times to receive a necessary backlash between a drum and a boot. Adjust a cable of a lay brake (for adjustment, address to Section Check and adjustment of a lay brake in the Head Brake system).
- Establish a back central console box.
|
|
Establish a wheel and tighten wheel nuts with the specified twisting moment of an inhaling. An inhaling twisting moment: a wheel nut (b): 100 Н•м (10.0 kg th, 72.5 pounds-foots). |
- Check up and be convinced that a brake drum not заедает and brakes work correctly. Then remove a vehicle from the lift and execute brake check (a foot brake and a lay brake).
|
|
Brake колодка
Removal
|
|
- Execute item 1 - 5 procedures of removal Has undressed the Brake drum.
|
|
Be especially cautious, establishing a returnable spring brake Pads. Wrong installation can lead to that the spring will come off and can become the trauma reason. |
|
|
- Remove the springs pressing a boot (1), having unbent the pins pressing a boot (2).
|
- Remove the top returnable spring (4), assemblage of a regulator (3), the lever of a regulator (5), a spring of the lever of a regulator (6), a spring of a rack (8), and сойку (7).
- Remove brake Pads and the bottom returnable spring of a boot (9).
- Remove brake Pads and disconnect a cable of a lay brake (2) from the lever Pads a lay brake (1).
|
|
3 — a branch pipe of a brake cable |
|
|
- Remove the lever Pads a lay brake (2) and the holder (1) with brake Pads (3).
|
|
|
Survey
The lever of a lay boot
|
|
Examine the lever brake Pads and check up, whether movement concerning brake Pads is free. If it is faulty, correct or replace.
|
Regulator assemblage
|
|
Check up a carving or a ratchet of a rack and a regulator, whether there is no deterioration, jamming and corrosion.
|
Springs
|
|
- Examine are not damaged and whether ослабли springs.
|
|
- Examine each part with an arrow, whether there is no rust. If there are malfunctions, replace.
|
|
|
Brake колодка
Address to subsection Survey Has undressed the Brake drum.
Installation
|
|
- Collect parts in an order, the return to an order at removal.
|
|
1 — the bottom returnable spring
2 — the bottom rack |
|
|
- Establish the springs keeping a boot (1) having pressed down of them into place and turning clamping pins (2).
|
- Establish assemblage of a regulator (3) and the top returnable spring of a boot (4).
- Establish the lever of a regulator (5), a spring of the lever of a regulator (6), assemblage of a rack (7) and a spring of a rack (8).
- Establish the bottom returnable spring of a boot (9).
- Then address to Section the Brake drum.
|
|
|
|