Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation


Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
- Brake system
   + Brakes
   + Brake highway/hose the brake cylinder
   + Forward brakes
   - Lay and back brake
      + The general description
      - Diagnostics
         Check and adjustment
         Vehicle service
         Cable of a lay brake
         Brake drum
         Brake колодка
         The brake cylinder
         Back plate of a brake
   + Antiblocking brake system (ABS)
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment



Cable of a lay brake

A — Kind A
B — Kind B
With — Kind C
D — Kind D
E — Kind E
1 — the switch of a lay brake
2 — the lever of a lay brake
3 — a bolt of a lay brake
4 — a floor
5 — a lock nut
6 — a lining
7 — the check
8 — the balance weight

9 — a regulator pin
10 — сцепка
11 — a colour tape (or a ring)
12 — a brake cable
13 — a condensing ring
14 — a clip bolt
15 — a clip (if the car is equipped by it)
16 — a cross-beam
17 — a chassis frame
18 — a hook
19 — a back shaft
20 — a clip
21 — a clip (if is)


Inhaling twisting moment.

Removal

 PERFORMANCE ORDER

  1. Remove a brake drum (address to item 1 - 6 procedures of removal Has undressed the Brake drum).
  2. Check up colour of a ring or a tape for reinstallation.

The colour ring on a brake cable serves for identification.

  1. Disconnect a cable of a lay brake from the lever brake Pads (address to item 2 - 5 procedures of removal of Section Brake колодка).
  2. Disconnect a brake cable from a back plate of a brake (address to item 4 of procedure of removal of Section the Back plate of a brake of the given Chapter).

When it is necessary to remove cables and the right and left lay brake, repeat the steps described above for the right and left wheels.

  1. Remove a cable about the lever of a lay brake (address to item 1 and 4 - 6 procedures of removal Has undressed the Lever of a lay brake).

Installation

 PERFORMANCE ORDER

  1. Establish parts in an order, the return to removal procedure, having paid attention to the following.
  2. Establish a cap of a brake cable (2) on a back plate of a brake (1) having fixed it.

The colour ring or tape on a brake cable serve for identification. Use a cable with the same colour ring, as before removal.


1 — a back plate of a brake
2 — a cap of a brake cable
3 — a brake cable
  1. Establish a spring of a brake cable (2) and a branch pipe (3) on the lever Pads a lay brake (1) and fix.
  1. For installation brake Pads, address to item 1 - 5 procedures of installation of Section Brake колодка.
  2. For installation of a brake drum, address to Section the Brake drum.
  3. Correctly stretch and reliably fix clips a cable of a lay brake.
  4. For cable installation on the lever of a lay brake, address to subsection Installation Has undressed the Lever of a lay brake.
  5. On installation end, adjust a cable (address to Section Check and adjustment of a lay brake in the Head Brake system). Then check up, whether there is no jamming of a brake drum, and whether the brake system correctly works. After removal of a vehicle from the lift it is necessary to inspect a brake.