- For installation of a fist, an oil epiploon of an axis of a fist of a wheel and the bearing of a shaft of a drive (2) execute in return sequence of manipulation on removal, paying attention to the following.
The all-wheel drive car
|
|
1 — an axis of a fist of a wheel
3 — a persistent washer of a shaft of a forward drive (type “C” or “D”)
4 — an internal oil epiploon
6 — an oil epiploon of a shaft of a drive
With — flat type
D — фланцевый type (for a cabriolet) |
The car with a drive on two wheels
|
|
1 — an axis of a fist of a wheel
5 — a fist cap
|
For the all-wheel drive car
- By means of the special tool establish the bearing of a shaft of a drive (1).
- The special tool:
- (A): 09913-76010 — a persistent washer of a shaft of a drive of type With
- (A): 09913-80112 — a persistent washer of a shaft of a drive of type D
- Persistent washer of a shaft of a drive of type And
- The size “a”: 0 – 1 mm (0 – 0.04 inches)
- Persistent washer of a shaft of a drive of type In
- The size “a”: 1.75 – 2.50 mm (0.069 – 0.098 inches)
- At installation of an axis of a fist of a wheel on a fist, process adjoining surfaces hermetic. “A”: hermetic 99000-31110.
For the all-wheel drive car
|
|
- Besides, fill a flute in an axis of a fist of a wheel approximately with ten grammes plastic литиевой greasings. “B”: greasing 99000-25010.
|
|
|
- Tighten a nut of an axis of a fist of a wheel to the specified value of the moment of an inhaling. The inhaling moment: a nut of an axis of a fist of a wheel (a): 50 Н•м (5.0 kg th, 36.5 pounds-foots).
|
For the all-wheel drive car
- Pressing establish an internal oil epiploon.
|
|
- By means of the special tool enter inside an internal oil epiploon while its end will not concern a step surface of a fist.
- The special tool:
- (B): 09944-66010
- (C): 09924-74510
|
For the all-wheel drive car
- Put plastic литиевую greasing on an edge of an oil epiploon and in its cavity, having filled it more, than on 60 %.
- Put литиевую plastic greasing “A” on a shaft of a drive (2). “A”: greasing 99000-25010.
- Pressing establish a persistent washer of a shaft of a forward drive (3) on a shaft of a drive (2) if it has been removed (for a persistent nut of a shaft of a drive of type). Put литиевую plastic greasing “A” on a persistent washer of a shaft of a drive. “A”: greasing 99000-25010.
- Put литиевую plastic greasing “A” and establish a persistent washer of a shaft of a forward drive (3) rounded off by the party to the central party (for a persistent washer of a shaft of a drive of type). “A”: greasing 99000-25010.
|
|
Type With — a flat washer
Type D — развальцованная a washer |
For the car with a drive on two wheels
- Remove greasing, old hermetic and a dirt from adjoining surfaces of a cap of a fist (2) and a fist (1), on a pure surface of a cap in regular intervals put water-proof hermetic and establish a cap on a fist. “B”: hermetic 99000-31090.
|
|
1 — a fist
2 — a fist cap
3 — a wheel spindle |
|
|
- Tighten a nut of the lever of a hairpin with a spherical tip. For this purpose take a new nut and tighten it to the specified value of the moment of an inhaling. The inhaling moment: a nut of a hairpin with a spherical tip (a): 60 Н•м (6.0 kg th, 43.5 pounds-foots).
|
For the car with a drive on two wheels
|
|
- Put water-proof hermetic on an adjoining surface of a nave of a wheel (1) and establish a cap of a nave (2) on a wheel nave. “A”: hermetic 99000-31090.
|
For the all-wheel drive car
|
|
- At installation of a flange of a drive of the bridge (1) on a wheel nave, put hermetic on an adjoining surface of a flange of a drive of the bridge (1). “A”: hermetic 99000-31090. The inhaling moment: a bolt of a flange of a drive (a): 50 Н•м (5.0 kg th, 36.5 pounds-foots).
|
- For installation of a nave of a wheel see in the given Chapter Has undressed a wheel Nave (including the wheel bearing).
|
|
- Connect a tip of steering draught to a fist and tighten a new nut of a tip of steering draught. The inhaling moment: a nut of a tip of steering draught (a): 40 Н•м (4.0 kg th, 29.0 pounds-foots).
|
|