Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
- Suspension bracket
- Forward suspension bracket
The general description
+ Diagnostics
- Service out of a workshop
The stabilizer of cross-section stability/plug
Shock-absorber rack
Cylindrical spring
The terminator of a dynamic course of a suspension bracket / a rubber nest of a spring
Wheel nave (including the wheel bearing)
Sharnir/os rotations
The suspension bracket/plug lever
+ Back suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Cylindrical spring
Removal
|
|
- Lift the car that the forward suspension bracket freely hung.
- Remove wheels.
|
|
- Remove a flange of a drive of an axis of a shaft (at the all-wheel drive car).
|
|
|
- Remove a spring ring of a shaft of a forward drive (1) (at the all-wheel drive car).
|
|
|
- Remove bolts of a support of a disk brake and hang up a support on a wire hook (1).
|
|
|
Hang up the removed support of a disk brake on a wire hook that the brake hose was not bent and it was not overwound and it was not stretched. Do not press a brake pedal when are removed brake Pads. |
|
|
- If there is a system of antiblocking of brakes (ABS), remove a bolt of the plug of a wire (2) and remove the gauge of speed of a forward wheel (1) from a pin.
|
|
|
- Do not pull a wire when remove the gauge of speed of a forward wheel (1).
- Do not damage a surface of the gauge of speed of a forward wheel (1) and track, that the dust has not got to its aperture for installation, a dirt, etc.
|
|
|
If it is impossible to remove a disk hands, take advantage of 8-millimetric bolts. |
- Remove a bar of the stabilizer of cross-section stability as it is described in the given Chapter in Section the Stabilizer of cross-section stability/plug, (point Removal).
|
|
- Disconnect a tip of steering draught from a rotary pin by means of a stripper.
|
|
|
- Jack prop up the bottom lever.
|
|
|
- Remove bolts скобы racks.
|
- Remove a nut of a hairpin with a spherical tip.
|
|
- By means of a stripper disconnect a rotary pin from a hairpin with a spherical tip.
|
- Lowering a jack, remove a rotary pin and a wheel nave.
|
|
- Remove a cylindrical spring (1).
|
|
|
Installation
|
|
- For installation of a cylindrical spring execute in return sequence of manipulation on its removal.
|
|
The top and bottom diameters of a cylindrical spring неодинаковы. The end with the big diameter put downwards, and the free end establish in a nest of a spring (1). |
- At a tightening of all болтовых connections observe the specified values of the moment of an inhaling.
- As to a nut of a hairpin with a spherical tip, do not forget to insert шплинт and to bend it after a nut tightening.
- Tighten a nut of a tip of steering draught a hairpin with spherical tips upwards that the hairpin did not rotate.
For the all-wheel drive car
|
|
a. For a washer of a shaft of a forward drive and an external axis of a fist of a forward wheel use литиевую plastic greasing. “A”: cмазка 99000-25010.
|
For the all-wheel drive car
|
|
b. At installation of a cutting lock ring (1) on a drive shaft use болтовое an aperture in a drive shaft to pull out it and to turn in the big diameter (2) rings to the right.
|
For the all-wheel drive car
|
|
c. At installation of a flange of a drive of an axis of a shaft (1) on a wheel nave put hermetic on an adjoining surface of a flange of a drive of an axis of a shaft and tighten a bolt of a flange (2) to the specified value of the moment of an inhaling. “A”: hermetic 99000-31090. The inhaling moment: a bolt of a flange of an axis of a shaft (a): 50 Н•м (5.0 kg th, 36.5 pounds-foots).
|
|
|
- Check up, that no alien material has stuck to the gauge and a rotor. Establish the gauge of speed of a wheel (1) and the plug of its fastening.
- The inhaling moment:
- Bolt of the plug of fastening (a): 10 Н•м (1.0 kg th, 7.5 pounds-foots)
- Bolt of the gauge of speed (b): 23 Н•м (2.3 kg th, 17.0 pounds-foots)
|
|
|
At installation of the gauge of speed of a forward wheel do not pull and do not overwind excessively connecting wires. Reliably attach a sealing ring to an internal wing. |
- Check up, that there was no backlash between the gauge and a fist.
|
|
|
|