Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
+ Mechanical part of engine G16
+ Mechanical part of engine J20
- Engine cooling
+ The general description
+ Diagnostics
- Maintenance service
Check of level of a cooling liquid
Service and repair of system of cooling
Washing and filling of system of cooling
Regulation and check of a tension of a belt of the cooling fan
+ Vehicle routine maintenance
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Regulation and check of a tension of a belt of the cooling fan
|
|
Disconnect a negative cable from the accumulator before to check and regulate a belt tension. |
For engines G16
|
|
- Check up a belt on presence of cracks, cuts, deformations, deterioration and cleanliness. If what not so, replace a belt.
- Check up a belt tension. The belt tension is considered correct when it caves in according to following technical requirements under the pressure of a thumb (about 10 kg or 22 pounds). A tension of a belt of the cooling fan (for models of engines G16) "and": 5 – 7 mm (0.20 – 0.28 inches) sag under the pressure of 10 kg (22 pounds).
|
|
At replacement of a belt on new adjust a tension of a belt to 5 – 6 mm (0.20 – 0.24 inches) (engine G16). |
Engine G16
|
|
1 — 10 kg (22 pounds)
2 — an adjusting bolt
3 — шарнирный a bolt |
| |
- If a belt will pull too poorly or too strongly, adjust its tension, having displaced generator position.
|
- Twirl an adjusting bolt and шарнирный a generator bolt.
- Connect a negative cable (-) to the accumulator.
|
|
For engines J20
|
|
- Examine a belt about cracks, cuts, deformations, deterioration and cleanliness. If what not so, replace a belt.
- Check up a belt tension. The belt tension is considered normal when it sags according to following technical requirements under the pressure of a thumb (about 10 kg or 22 pounds). A tension of a belt of the cooling fan (for engines of model J20) "and": sags on 5 – 7 mm (0.20 – 0.27 inches) under weight/10 of kg (22 pounds).
|
|
At replacement of a belt on new, adjust a tension of a belt to 4 – 5 mm (0.16 – 0.20 inches). |
Engine J20
|
|
1 — 10 kg (22 pounds)
2 — an adjusting bolt
3 — a pulley коленвала
4 — a fan pulley
5 — шарнирный a bolt |
- If a belt will pull too hardly or too poorly, adjust it as follows:
|
|
- Loosen the an adjusting bolt (1) and шарнирный a bolt (2).
|
- Twirl an adjusting bolt (1), keeping at this time a fan belt in a corresponding tension, twisting высоконапряженный a bolt with the control of loading (3) wrench.
- Fasten an adjusting bolt (1) and шарнирный a bolt (2) with the specified rotating moment.
|
|
- The rotating moment of an inhaling:
- Adjusting bolt of a pulley of the cooling fan (for engine J20) (): 45 Н•м (4.5 kg th, 32.5 pound on foot)
- шарнирный a bolt of a pulley of the cooling fan (for engine J20) (b): 45 Н•м (4.5 kg th, 32.5 pound on foot)
|
|
|
|
|