Suzuka Grandee Vitara
+ The general information
- Maintenance service and greasing
+ Service
- Maintenance service
- The engine
Privodnoj belt
Belt ГРМ (only for engines G16)
Klapannyj backlash (only for engines G16)
Engine oil and the filter
Cooling liquid
Exhaust system
+ Ignition system
+ Fuel system
+ System of decrease in toxicity of an exhaust
+ The chassis and body
Definitive survey
Recommended liquids and lubricants
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
+ Engines
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Maintenance service
The engine
Privodnoj belt
|
|
Any check and replacement of spare parts are carried out only on the idle engine. |
Check of a belt of the generator and the cooling pump (on engines G16)
|
|
- Disconnect "weight" from АКБ.
- Believe a belt on cracks, anguishes, deformation, deterioration and cleanliness.
- At detection of any defect replace a belt.
- Check up a belt on a tension.
- Tension of a belt of the generator and cooling pomp:
- "And" — a deflection 5 — 7 mm (0.20 — 0.28 inches) for G16.
|
|
1 — a pulley of a cranked shaft
2 — a pulley of the water pump
3 — 100 Н, 10 kg or 22 pounds
|
|
|
At replacement of a belt on new, adjust a tension of a belt to a deflection 5 — 6 mm (0. 20 — 0. 24 inches) for G16. |
- If a belt will draw or it is too poorly tense, adjust to norm, by generator moving.
- Tighten an adjusting bolt of the generator and шкворень.
- Connect "weight" to АКБ.
|
|
Replacement of a belt of the generator and cooling pomp (on engines G16)
Replace a belt. The Belt of the cooling fan in the Head Cooling of the engine for procedure of replacement of a belt of the water pump see.
Check drive a belt of the pump of cooling, the generator, the amplifier of a wheel, the conditioner compressor (if it is provided)
|
|
Type and — dark green labels on натяжителе
Type b — yellow labels on натяжителе
“A” — The indicator
“a” — Area of a normal tension
“b” — Limiting area
“c” — Area of excess of a limit.
|
|
|
- Disconnect "weight" from АКБ.
- Check up a belt on cracks, anguishes, deformation, deterioration and cleanliness.
- At detection of any defect replace a belt
- Check up, that the indicator натяжителя A was in area a.
- If indicator "A" is in a zone c, having passed b replace a generator belt with the new.
|
|
Use a mirror at check of a tension of a belt натяжителя type "And". |
|
|
Replacement drive a belt of the pump of cooling, the generator, the amplifier of a wheel, the conditioner compressor (if it is provided) (on engine J20)
Replace a belt according to procedure of replacement of a belt of the generator in the Head electric equipment System.
Check drive a belt of the fan of cooling of the engine (for engine J20)
|
|
1 — 100 Н, 10 kg or 22 pounds
2 — муфта the fan
3 — муфта коленвала
4 — an adjusting bolt and шкворень
|
|
|
- Disconnect "weight" from АКБ.
- Check up a belt on cracks, anguishes, deformation, deterioration and cleanliness.
- At detection of any defect replace a belt
- Check up a belt on a tension
- Tension of a belt of the fan of cooling:
- a — A deflection in 5 – 7 mm (0. 20 – 0. 27 inches) under loading 100 Н, 10 kg or 22 pounds.
|
|
At replacement of a belt on new, adjust a tension of a belt to a deflection 4 — 5 mm (0. 16 — 0. 19 inches) for G16. |
- If a belt will draw or it is too poorly tense, adjust to norm, by adjustment of a pulley of the fan of cooling.
- Tighten an adjusting bolt of the generator and шкворень.
- Connect "weight" to АКБ.
|
|
Replacement of a belt of the fan of cooling (on engine J20)
Replace, according to replacement procedure drive a belt of the fan of cooling in Section the Belt of the cooling fan in the Head engine Cooling.
Check drive a belt of the pump of the hydraulic booster of a wheel and the conditioner compressor (if it is established) (on engines G16)
|
|
1 — a pulley коленвала
2 — a pulley of the pump of the hydraulic booster of a wheel
3 — a pulley of the compressor of the conditioner (if it is equipped)
4 — a pulley натяжителя a belt
5 — pulley bolts натяжителя
[A]: G16 with P/S
[B]: G16 with P/S and A/C
|
|
|
- Disconnect "weight" from АКБ.
- Check up a belt on cracks, anguishes, deformation, deterioration and cleanliness.
- At detection of any defect replace a belt.
- Check up a belt tension
- Tension of a belt of the pump of the hydraulic booster of a wheel and the conditioner compressor:
- a — A deflection in 6 – 9 mm (0.24 – 0.35 inches) under loading 100 Н, 10 kg or 22 pounds.
- b — A deflection in 4 – 7 mm (0.16 – 0.28 inches) under loading 100 Н, 10 kg or 22 pounds.
- If the tension of a belt falls outside the limits the given specification, adjust according to Razdelom Privodnoj a belt of the pump of the hydraulic booster of a wheel in the Head System of the hydraulic booster of a wheel.
- Connect "weight" to АКБ.
|
|
Replacement drive a belt of the pump of the hydraulic booster of a wheel and-or the conditioner compressor (if it is established) (on engines G16)
Replace a belt and then adjust its tension according to the procedure of replacement of a belt described in Razdele Privodnoj a belt of the pump of the hydraulic booster of a wheel in the Head System of the hydraulic booster of a wheel.
|
|