Suzuki Grand Vitara SQ416/SQ420/420WD

Since 1998 of release

Repair and car operation

Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
   - Mechanical part of engine G16
      + The general description
      - Routine maintenance
         Compression check
         Check of depression of the engine
         Check of pressure of oil
         Klapannyj backlash
         Filtering element of the air filter
         Cover of a head of cylinders
         The case throttle заслонок and an inlet collector
         Collector of the fulfilled gases
         Drive belt газораспределительного the mechanism and the tension device for a belt
         Маслосборник and a grid of the oil pump
         The oil pump
         Коромысло the valve, an axis коромысел and a cam-shaft
         Valves and head of the block of cylinders
      + Piston rod, piston rings, rods and cylinders
      The special tool
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
   + Mechanical part of engine J20
   + Engine cooling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment

Klapannyj backlash

PERFORMANCE ORDER

Disconnect a negative cable from the accumulator.
Uncover heads of cylinders, having addressed to Section the Cover of a head of cylinders in this Chapter.

Using 17 mm the plug, turn a pulley of a cranked shaft (1) clockwise while the mark V (a white paint) (2) on a pulley will not be made even to "the 0" (zero) calibrated on a cover of a belt of a drive газораспределительного of the mechanism.

Check up, whether are коромысла valves of the cylinder №1 out of corresponding contours of a cam (cam-shaft); if it so, valves (1), (2), (5) and (7) in drawing are ready to check and backlash adjustment. Check up клапанные backlashes on valves (1), (2), (5) and (7). If коромысла valves of the cylinder №4 are out of corresponding contours of a cam, check up клапанные backlashes on valves (3), (4), (6) and (8).

At check клапанного a backlash insert калибромер between a cam-shaft and a working surface of a cam коромысла the valve.

If клапанный the backlash does not correspond to technical characteristics, adjust it according to technical characteristics, turning the adjusting screw, preliminary having weakened a counternut. After adjustment fasten a counternut to the specified rotating moment, simultaneously keeping the adjusting screw motionlessly, and then be again convinced that клапанный the backlash corresponds to technical requirements.

Technical characteristics клапанного a backlash

	When it is cold (antifreeze temperature makes 15 – 25С or 59 – 77F)	When hot (the antifreeze temperature makes 60 – 68С or 140 – 154F)
On an input	0.13 – 0.17 mm (0.005 – 0.006 inches)	0.17 – 0.21 mm (0.007 – 0.008 inches)
On an exit	0.23 – 0.27 mm (0.009 – 0.010 inches)	0.28 – 0.32 mm (0.011 – 0.012 inches)

Special инструмент6 () — 09917-18211. The rotating moment of an inhaling: a counternut of the adjusting screw коромысла the valve () — 12 Н•м (1.2 kg th, 9.0 pound on foot).

1 — калибромер

After check and adjustment клапанных backlashes on valves (1), (2), (5) and (7), (or (3), (4), (6) and (8)) turn коленвал precisely on 360 degrees (one complete revolution) and check up too most on valves (3), (4), (6) and (8) (or (1), (2), (5) and (7)).

Adjust them as it is necessary.

After check and adjustment of all valves, repeat dismantling procedure upside-down for the purpose of installation.

home