Suzuka Grandee Vitara
+ The general information
+ Maintenance service and greasing
+ Heater, ventilation and the conditioner
+ Steering
+ Suspension bracket
+ Wheels and tyres
+ Forward приводной a shaft shaft/bearing. An oil epiploon
+ Kardannye shaft
+ Brake system
- Engines
- Mechanical part of engine G16
+ The general description
- Routine maintenance
Compression check
Check of depression of the engine
Check of pressure of oil
Klapannyj backlash
Filtering element of the air filter
Cover of a head of cylinders
The case throttle заслонок and an inlet collector
Collector of the fulfilled gases
Drive belt газораспределительного the mechanism and the tension device for a belt
Маслосборник and a grid of the oil pump
The oil pump
Коромысло the valve, an axis коромысел and a cam-shaft
Valves and head of the block of cylinders
+ Piston rod, piston rings, rods and cylinders
The special tool
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
+ Mechanical part of engine J20
+ Engine cooling
+ Fuel system
+ Ignition system
+ Start system
+ Release system
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. An immobilizer
+ Electric equipment
|
Маслосборник and a grid of the oil pump
Components
|
|
Put hermetic 99000-31250 on the interfaced surfaces маслосборника and the block of cylinders, having addressed to subsection Installation. |
|
|
The rotating moment of an inhaling. |
Removal
|
|
- Lift a vehicle.
- Remove the case of forward differential (1) with differential (2), having addressed to Section Removal in the Head Forward differential.
|
|
1 — the case of forward differential
2 — differential
3 — маслосборник |
- Disconnect муфту the gauge of an angle of rotation коленвала and remove the gauge of an angle of rotation коленвала, having turned off its bolt (if that is available).
- Merge engine oil, having opened a drain stopper (2).
|
|
1 — маслосборник
2 — a drain stopper |
|
|
- Remove the bottom plate of the case муфты (cases of the hydrotransformer for А/Т) (1).
|
- Remove маслосборник (3) and then a grid of the oil pump (2).
|
|
1 — the block of cylinders
2 — a grid of the oil pump
3 — маслосборник |
|
|
Cleaning
|
|
|
|
- Clear the interfaced surfaces маслосборника and the block of cylinders.
|
|
|
- Remove oil, old hermetic and a dust from the interfaced surfaces and inside маслосборника.
|
|
|
- Clear a grid of the oil pump.
|
|
|
Installation
|
|
- Put hermetic on the interfaced surface маслосборника continuously. "And": hermetic 99000-31250.
|
|
"And" — 2 mm (0.05 inches)
b — 3 mm (0.12 inches) |
- Place new consolidation (2) in that place.
|
|
- Establish a grid of the oil pump (1) and маслосборник (3). At first twirl a grid bolt, and then an arm bolt by the specified rotating moment.
- The rotating moment of an inhaling:
- Bolt of a grid of the oil pump (): 11 Н•м (1.1 kg th, 8.0 pound on foot)
- Bolt of an arm of a grid of the oil pump (b): 11 Н•м (1.1 kg th, 8.0 pound on foot)
|
- After adjustment маслосборника to the block of cylinders, insert tightening bolts and start to tighten at the centre: turn a wrench outside, twisting on one bolt at a time.
|
|
- Fasten bolts and nuts to the specified rotating moment. The rotating moment of an inhaling: a bolt and a nut маслосборника () — 11 Н•м (1.1 kg th, 8.0 pound on foot).
|
|
|
- Insert a new lining and a drain stopper in маслосборник (1). Fasten a drain stopper to the specified rotating moment. The rotating moment of an inhaling: a drain stopper () — 50 Н•м (5.5 kg th, 36.5 pound on foot).
|
|
|
- Establish the bottom plate of the case муфты (hydrotransformer) (1).
|
|
|
- Establish the gauge of an angle of rotation коленвала (1) and connect it муфту. The rotating moment of an inhaling: a bolt of the gauge of an angle of rotation коленвала () — 10 Н•м (1.0 kg th, 7.5 pound on foot).
|
- Establish the case of forward differential with differential, having addressed to Section Installation in the Head Forward differential.
- Fill the case of forward differential трансмиссионным with oil, having addressed to Section Servicing in the Head Forward differential.
- Fill in the engine with engine oil, having addressed to Section Engine oil and the filter in the Head Maintenance service and greasing.
- Check up, whether leaks engine oil and трансмиссионное oil from outside each connection.
|
|
|
|